Roland VP-330 Repair

Dieses Thema im Forum "Analog" wurde erstellt von acidblue0, 21. November 2005.

  1. acidblue0

    acidblue0 Tach

    Not sure where I should be asking this. I;m looking to get m

    Not sure where I should be asking this. I;m looking to get my Roland VP-330 Vocoder fixed up. The carrier sound is bleeding over when I vocoder.
     
  2. Wenns blutet - einfach ein Pflaster drauf.

    Gruss,

    Co


    Wenns blutet - einfach ein Pflaster drauf.

    Gruss,

    Cornel
     
  3. Moogulator

    Moogulator Admin

    welcome again.. well.. it's hard to tell via the net, my ser

    welcome again.. well.. it's hard to tell via the net, my service link is quite focused on germany.. <a href=http://sequencer.de/synth/index.php/Synthesizer_Repair>Reparatur / Service</a>

    but I think you need some service, then..

    bleeding over? hmm.. and it worked fine before?..
    there is ofter some sort of dry/wet control.. (ok, thats silly.. perhaps it is good to know)..

    what exactly do you mean with bleeding over? crosstalk?
     
  4. acidblue0

    acidblue0 Tach

    Thanks for the reply. I have e-mailed all links and got no a

    Thanks for the reply. I have e-mailed all links and got no answer yet. Yeah when I vocode I can hear the waveform just a little when I talk. Don;t sound that bad on lower notes but on higher notes its shows bad. I just got vocoder and guy said it has been sitting up for 15 years without any use. So I;m pretty sure it is something simple but there is no old school tech in my area. Thanks for any help. Maybe I can make an mp3 and show you what I;m talking about.
     
  5. Moogulator

    Moogulator Admin

    and you are sure it is not something to set on the panel ..?

    and you are sure it is not something to set on the panel ..?

    but anyway, it sounds very much like you need to send it in.. well, depends on where you live atm..
     
  6. acidblue0

    acidblue0 Tach

    I'm in the US but I don't mind paying shipping to get it wor

    I'm in the US but I don't mind paying shipping to get it working.
     
  7. Jörg

    Jörg |

    You could contact one of those (all in the US):

    Audio Ele


    You could contact one of those (all in the US):

    Audio Electronics
    www.audioelectronics.com
    10870 Plano Rd.
    Suite C
    Dallas TX 75238
    214/349-5000 or 800/466-2372

    SYNERGY DIGITAL SOUND RESOURCES
    409 West Apollo Avenue
    Bismarck ND 58503
    (701)258-9046 (Attn: Keith)
    synergydss@mybluelight.com (email)

    EPR ProAudio Electronics
    1242 E. Hillsborough Avenue
    Tampa, Florida 33604
    http://eprelectronics.com/

    //California - Bay Area//
    www.analogsynthservice.com
    Greg Montalbano.

    Northeast Ohio, Cleveland area:
    Beamish Electronics
    4560 State Rd.
    Parma, Ohio
    216-351-9599

    Stolen from VSE:
    http://www.vintagesynth.org/phpBB2/view ... 90&start=0
     
  8. Moogulator

    Moogulator Admin

    perfect, so I do not have to work ;-)
    there are sooo many go


    perfect, so I do not have to work ;-)
    there are sooo many good service staiton in the US, I am sure you do not need to send it to germany..
     
  9. acidblue0

    acidblue0 Tach

    Thanks. I will start calling these guys today.

    Thanks. I will start calling these guys today.
     
  10. acidblue0

    acidblue0 Tach

    I just sent my vocoder to Dallas (www.audioelectronics.com).

    I just sent my vocoder to Dallas (www.audioelectronics.com). The tech their has fixed a few of these with the same problem. So I feel a lot better now.
     
  11. Moogulator

    Moogulator Admin

    looks like some *typical* weak point here.. good luck!! look

    looks like some "typical" weak point here.. good luck!! looks good!!
     
  12. ppg360

    ppg360 fummdich-fummdich-ratata

    Did you get in touch with Tom Moravansky at synthservices.co

    Did you get in touch with Tom Moravansky at synthservices.com? Tom is located in Maryland, and I´d get in touch with him first. Even if he can´t fix carrier bleedthrough on a VP 330 (which should be an easy fix), he may know someone who can.

    Stephen
     
  13. acidblue0

    acidblue0 Tach

    I already sent it to Dallas. But if he can't fix I will try

    I already sent it to Dallas. But if he can't fix I will try him next. THANKS
     

Diese Seite empfehlen